Firemaking – How to Make a Fire

Who doesn’t love sitting around a fire on a cool fall night, or a crackling fireplace? But what if you needed to start a fire for survival? Do you have the firemaking skills required for your survival?

First thing is to know the basics of fire safety and fire starting:

  • Always light your fire from the upwind side.
  • Make sure to lay your tinder, kindling, and fuel so that your fire will burn as long as you need it.
  • Igniters provide the initial heat required to start the tinder burning.

 

Firemaking skills fall into two categories: modern methods and primitive methods.

Modern Methods for Firemaking

Modem igniters use modem devices–items we normally think of to start a fire.

  • Matches: Make sure these matches are waterproof. Also, store them in a waterproof container along with a dependable striker pad.
  • Convex Lens: Use this method only on bright, sunny days. The lens can come from binoculars, camera, telescopic sights, or magnifying glasses. Angle the lens to concentrate the sun’s rays on the tinder. Hold the lens over the same spot until the tinder begins to smolder. Gently blow or fan the tinder into flame, and apply it to the fire lay.
  • Metal Match: Place a flat, dry leaf under your tinder with a portion exposed. Place the tip of the metal match on the dry leaf, holding the metal match in one hand and a knife in the other. Scrape your knife against the metal match to produce sparks. The sparks will hit the tinder. When the tinder starts to smolder, proceed as above.
  • Battery: Use a battery to generate a spark. Use of this method depends on the type of battery available. Attach a wire to each terminal. Touch the ends of the bare wires together next to the tinder so the sparks will ignite it.
  • Gunpowder: Often, you will have ammunition with your equipment. If so, carefully extract the bullet from the shell casing, and use the gunpowder as tinder. A spark will ignite the powder. Be extremely careful when extracting the bullet from the case.

 

Primitive Methods for Firemaking

Primitive igniters are those attributed to our early ancestors.

  • Flint and Steel: The direct spark method is the easiest of the primitive methods to use. The flint and steel method is the most reliable of the direct spark methods. Strike a flint or other hard, sharp-edged rock edge with a piece of carbon steel (stainless steel will not produce a good spark). This method requires a loose-jointed wrist and practice. When a spark has caught in the tinder, blow on it. The spark will spread and burst into flames.
  • Fire-Plow: The fire-plow is a friction method of ignition. You rub a hardwood shaft against a softer wood base. To use this method, cut a straight groove in the base and plow the blunt tip of the shaft up and down the groove. The plowing action of the shaft pushes out small particles of wood fibers. Then, as you apply more pressure on each stroke, the friction ignites the wood particles.
  • Bow and Drill: The technique of starting a fire with a bow and drill is simple, but you must exert much effort and be persistent to produce a fire. You need the following items to use this method:
    • Socket: The socket is an easily grasped stone or piece of hardwood or bone with a slight depression in one side. Use it to hold the drill in place and to apply downward pressure.
    • Drill: The drill should be a straight, seasoned hardwood stick about 2 centimeters in diameter and 25 centimeters long. The top end is round and the low end blunt (to produce more friction).
    • Fire board. Its size is up to you. A seasoned softwood board about 2.5 centimeters thick and 10 centimeters wide is preferable. Cut a depression about 2 centimeters from the edge on one side of the board. On the underside, make a V-shaped cut from the edge of the board to the depression.
    • Bow. The bow is a resilient, green stick about 2.5 centimeters in diameter and a string. The type of wood is not important. The bowstring can be any type of cordage. You tie the bowstring from one end of the bow to the other, without any slack.

To use the bow and drill, first prepare the fire lay. Then place a bundle of tinder under the Vshaped cut in the fire board. Place one foot on the fire board. Loop the bowstring over the drill and place the drill in the precut depression on the fire board. Place the socket, held in one hand, on the top of the drill to hold it in position. Press down on the drill and saw the bow back and forth to twirl the drill. Once you have established a smooth motion, apply more downward pressure and work the bow faster. This action will grind hot black powder into the tinder, causing a spark to catch. Blow on the tinder until it ignites.

Note: Primitive fire-building methods are exhaustive and require practice to ensure success.

HELPFUL HINTS

  • Use nonaromatic seasoned hardwood for fuel, if possible.
  • Collect kindling and tinder along the trail.
  • Add insect repellent to the tinder.
  • Keep the firewood dry.
  • Dry damp firewood near the fire.
  • Bank the fire to keep the coals alive overnight.
  • Carry lighted punk, when possible.
  • Be sure the fire is out before leaving camp.
  • Do not select wood lying on the ground. It may appear to be dry but generally doesn’t provide enough friction.

The post Firemaking – How to Make a Fire appeared first on Downtown Homestead.

Source: http://downtownhomestead.com/firemaking-make-fire/

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s